Thickener sizing and the importance of testwork especially for paste

first_imgInternational Mining’s monster April issue, including the annual paste supplement is now with the printer. One article for which there was insufficient space is by Outotec’s Andrew McIntosh. He notes that “the sizing of equipment which achieves design requirements and is not conservatively oversized can influence both the financing of a project as well as its long term operational success.” His article goes back to basics, outlining the different options available in thickener sizing, from rudimentary through to highly comprehensive, and explains where each method is appropriate. When planning a project that includes thickening technology, a key element in the process is determining the sizing and expected performance for the thickener(s). This information will facilitate project layout and design, as well as define capital expenditure and operational cost estimates.As thickener performance will have a direct effect on overall plant operation, Process Performance Guarantees from suppliers are generally expected. In certain cases these guarantees are a pre-requisite for the project meeting financing approval, so can be a critical element at early stages.Thickener performance parameters, such as underflow densities and overflow clarities, and the effect of feed variables such as rise rate and solids loading rate, can vary greatly for different thickener feeds. Even for the same types of application, thickener performance will vary at different sites due to factors such as particle size, the presence of clays and organic materials, water chemistry, and the effects of upstream processes such as grind size and the use of reagents.Other parameters, such as the optimal feedwell slurry density for efficient flocculation, and the type and dosage of flocculant will also vary from application to application. These parameters will have an effect on the project’s capital and operational costs. For example, a particular application may require additional dilution of the incoming feed stream via the use of self-diluting systems (such as Autodil or Turbodil) to add supernatant liquor from the thickener surface into the feed stream, while another application may require underflow re-circulation to seed the flocculation process due to a highly dilute thickener feed.Thickener sizing methods Depending on the stage of the project, and whether or not samples of indicative feed material are available, a number of different methods can be used to determine thickener sizing. In general, these can be classified as: rule of thumb sizing, cylinder settling tests, and, lastly, dynamic thickener testwork. These methods differ in levels of complexity and outlay (in terms of time and effort as well as cost) and correspondingly vary in their level of accuracy:1. ‘Rule of thumb’Sizing is based upon experience with the particular thickening application, and is used in cases where indicative feed samples are not available, or for preliminary sizing purposes. Performance achieved at adjacent sites with similar feed types can be taken into account, if this data is available.Generally ‘rule of thumb’ sizing is used at the early stages of project conceptual studies and for preliminary budget pricing purposes. This method is the least accurate method of the three, as assumptions are made re feed material displaying ‘typical’ properties for that particular application, and site-specific factors (such as high clay levels) can be overlooked. For this reason, it would be unusual that a definitive supplier’s Process Performance Guarantee would be provided based upon rule of thumb sizing.Often, due to the low level of accuracy associated with this method of sizing, it is necessary to allow for high safety factors on the sizings. This can lead to conservative sizings and therefore larger size thickeners than required, driving up project costs unnecessarily. Conversely, where feed materials display particularly poor settling characteristics, it is possible for the thickener to be undersized, leading to process performance being below specification.2. Cylinder Settling TestsThese tests and the various mathematical methods developed to interpret their results (such as the Coe & Clevenger, Kynch, and Talmage & Fitch methods) were the traditional method for thickener sizing until the 1990s. These methods are a step up from rule of thumb sizing and provide more accuracy. Cylinder settling tests (or jar tests) can be conducted with a relatively small amount of indicative feed sample, less than that required for dynamic thickening testwork.From the results of cylinder settling tests, interpolations can be drawn as to the expected underflow density in the full size thickener. Optimal feedwell conditions for flocculation can also be ascertained.The downside of cylinder settling tests is the lack of accuracy compared to dynamic testwork, since they do not account for the effects present in full-scale thickening, such as the rotating mechanism. To compensate, it is again necessary to allow for additional safety factors.3. Dynamic thickener testworkThis is the method through which the most accurate thickener sizing and prediction of process performance is achieved.Most reputable and experienced thickener suppliers have developed a number of dynamic testwork units of various sizes and configurations. These dynamic test rigs are essentially scale versions of commercial thickeners, with feedwells, flocculant addition, underflow pumps, and rotating rake mechanisms to duplicate the full-scale thickening process.For example, Outotec carries out most dynamic testwork in a bench-scale 99 mm internal diameter test rig. Other tests rigs include a 190 mm internal diameter with extended wall height to simulate the additional compression in paste thickeners, and 1 m diameter test units of various sidewall depths. The 190 mm and larger tests rigs are used for paste thickening applications and other larger scale test campaigns.Generally, due to the amount of sample required, paste thickening and larger scale testwork campaigns are conducted on-site. This is also the case for bench-scale testwork for feed types expected to age significantly during transport or where the water quality characteristics will affect results of testwork.Dynamic testwork presents a number of benefits including: Ability to accurately ascertain the relationship between feed solids loading rate and underflow density and overflow clarity, and flocculation requirementsAny requirements for feed dilution or solids re-circulation to achieve optimal conditions for flocculation can be determinedThe safety factors necessary with less accurate sizing methods are not required. This leads to lower costs in most cases as smaller thickeners can be specifiedProcess guarantees are available on thickeners sized using this method, thus fulfilling any requirement for guaranteed thickener process performance.Ensuring that the most accurate testwork possible is utilised can mean the difference between achieving desired thickener performance and ‘almost’ achieving it. ‘Almost’ achieving process targets can lead to problems such as:Ability to accurately ascertain the relationship between feed solids loading rate and underflow density and overflow clarity, and flocculation requirementsUnnecessarily high operating costs due to non-optimised flocculant consumptionUnacceptable thickener overflow clarity, meaning possible inability to recycle plant process waterDownstream effects on other equipment in the circuit such as, for example, filter operationComplications with underflow pumping or other intended transportation methodsProblems with tailings disposal, such as unstable tailings deposition, tailings disposal volume consumed at a higher rate than envisioned, additional rehabilitation costsInadequate washing – CCD circuit.So, in summary, in the early stages of a project, rudimentary rule of thumb sizing can fulfil basic requirements. However, the temptation to scrimp on the costs and effort associated with testwork can have lasting ramifications. Comprehensive dynamic testwork performed on indicative feed samples ensures truly optimised thickener performance, achieving process targets and minimising operational costs. It can also avoid costly conservative oversizing, which can mean the difference between whether your project proceeds or not. As tends to be the case in life, investing a little bit of expense and effort up front can save substantial costs and avoid disappointment further down the track.Andrew McIntosh is currently Senior Proposals Engineer, Thickening in Sydney, Australialast_img read more

Read More →